Did you ever wanted to have something of your bow with you although you could not shoot it? Something unique and self made? I will show you how to build your very own pen out of an old arrow. Nothing you can buy anywhere but a pen with your own quality. Something unique with your own fingerprint. Interested? You should read further.

So what do we need for our project?

At the beginning we need to get certain things straight. What kind of pen do we want to make? Do we want a ball-pen or do we want a pencil? Each thing needs the perfect shaft size for it. A pencil will not fit into a small diameter carbon shaft. Maybe you want to make your own filler. We will concentrate on two different basic types of pens as a ground level you can start developing your own way.

After deciding what pen you want to create we can get the needed materials together.

We require:

  • an arrow in a diameter that fits to your purpose

  • a pen of your choice

  • nock

  • a set of vanes

  • some hot-melt adhesive

  • a lighter

  • something to underlay, a marker, a (hack)saw, sandpaper

If you not want to change the infilling of your arrow you can also choose any other adhesive but i recommend hot-melt adhesive because you can renew your pen if it is worn out. The choice of the shaft to use is defined by your supllies. Use what you have.

Layout One – The pencil

What do we do?

Removing the point from the shaft

Before we start we need to get everything set up right and you should be in the possibility to obtain everything i mentioned above. If you use your older arrows you need at first to remove the point and i possible also the nock. In most cases the point is glued into the shaft with some hot-melt adhesive so you can heat up the point and remove it with a pliers.

Now you can decide how long your arrow will be. I do not think that your pen should have the length of your arrow. If we think about an 30“ arrow we have the possibility to make between three or four arrows out of it!

To get the right length of your shaft put the pencil right beside the shaft and mark the position of the end.

Now you can cut the shaft in the desired length. If you have access to a professional arrow cutter just use it. There is no better way to get this job done. Otherwise you can use any saw for this purpose. Be careful with alloy/carbon or full carbon shafts as they will fray out if you make any mistake and the whole thing needs to be discarded. The best way is to saw the outer surface and turn the shaft some degrees so you can remove the parts with the needed caution.

After cutting the arrow shaft you should sand paper the edges until everything feels plane and smooth. Take your pencil and sharpen it before putting it into the arrow shaft. Heat the hot-melt adhesive up until it becomes something fluid and make a drop around the middle of the pencil and push it into the shaft.

Maybe the adhesive cools down to fast so you need to heat it up again and push it even further until the perfect position is achieved. Let it cool down so that everything sits right in place.

Now you can put a nock on your arrowpen and put the vanes in your favorite design on it.

If you want to sharpen your pencil just heat up the shaft and pull out the pencil far enough to sharpen it. Let the adhesive cool down and you are fine with it.

Layout Two – The ball-pen

Maybe you want to make your own ball-pen rather than a pencil. Be advised that this will take much more time. Take a ball-pen of your choice – it should be as thin as the arrow shaft you use – and take it to pieces. You can choose between two options now. Option one is to glue the refill for the pen direct into the shaft. Option two is to reassemble the ball-pen into the shaft which will take loads of time.

Take a look at the pieces you got from disassembling the pen. You should have the refill, a spring, some plastics and the body of the pen. The front end of the pen contains the spring and prevents it from disappearing. Take a saw and remove this part from the rest of the body. We will take this and glue it onto our arrow shaft. We can match the design with some color.

Now take a look at the other end of the body. As on the other end you should have an area where the body is a bit thinner than the rest. Further you should find the ‘module’ that enables the filling to change its position. We need that in our shaft.

Remove it with a saw and sandpaper it until it will fit into the inside.

As you can see i removed the plastic and sandpaperd it. Out everything together to see how long your pen needs to be. Mark your arrow shaft and cut it into the right length.

After this you need to fuse everything together.Check everything for its position and glue it together. Then check again for correct positions. Take the point we took forom the original pen and glue it onto the one side of the shaft. Do not forget to add the refill, the spring and the little plastic parts to the pen before adding the point.

Now put the vanes in your favorite design on it. Finito!

The finished product

There a hundreds of possibilities to make your individual and unique pen. Maybe you want to paint something onto it, maybe you like to engrave it. Just be creative with it!